Home > New Arrivals >

The Kick by Evolv
The Kick by Evolv

Images are for illustration purposes only. Actual color, finish and packaging may vary.

List Price: $45.00
Our Price: $35.00

Stock Status:Out Of Stock
Product Code: EVV-K

Description Warnings
The Kick was designed to be used with IMR batteries only.

DO NOT REMOVE THE CLEAR SHRINK-WRAP: It acts as a protective second layer of insulation against shorts.INSTALLING KICK MODULE: The Kick MUST be installed correctly. The bottom of the Kick must sit directly on the positive terminal of the battery (button end for button-top batteries). The top of the Kick (the end with the blue adjustment box) must be oriented towards the head of the device (never towards a device spring). The Kick is designed to be used in 18650 metal tube mods with an IMR 18490 or 18500 battery. Several device manufacturers are considering building extensions or longer tubes to permit the Kick to be used with the larger 18650 IMR batteries. The Kick may also be used with 18500 metal tube mods with an IMR 18350 battery.

GROUND SPRING: You will notice a small spring attached to the top (side edge) of the Kick. This has been carefully designed and is an ESSENTIAL component of the Kick for proper functioning. The spring MUST make contact with the grounded inner wall of the battery tube. If this spring does not make contact, the Kick will not function. SOME (few) DEVICES HAVE ANODIZED or POWDER COAT ON THE INSIDE OF THE BATTERY Compartment. This can interfere with the ground connection. These coatings must be removed at the point of contact with the ground spring.

NOTE: DEVICE TUBES VARY - The internal diameter is wider on some and narrower on others. Please do not use the Kick in tube mods with an internal diameter greater than 19.5mm.Setting your Power Level (watts setting): The adjustment potentiometer (blue box) is located on the top side of the Kick. In the center of the box is a white adjustment screw to be used for adjusting the Kick's power setting. The watts settings are marked ON THE CIRCUIT BOARD and can be seen around the pot/blue-box. NOTE: there are lines underneath each setting number, follow the lines to the corresponding watts setting. Turning the adjustment screw clockwise increases power and counter-clockwise decreases power. The settings range is from 5 watts to 10 watts. The Kick performs best with attys/cartos rated between 1.3 to 3.0 Ohms. You can use higher rated resistance but the Kick will not regulate well at the highest power levels if resistance is above 3 ohms. Unlike Variable voltage devices, the Kick does not need frequent adjustments.Once you find your preferred Power level, there is no need to constantly adjust it because the Kick will maintain that Power level even if you change attys/cartos and/or resistance.

You can use an under-load digital meter to see the volts as you change resistances and/or settings. AN ATOMIZER OR CARTOMIZER MUST BE ATTACHED TO THE METER OR YOU WILL NOT GET ANY READING.Low Battery Indicator: The Kick will detect, and stop functioning, when a battery charge level drops below 3.2 volts UNDER LOAD (with an atty/carto attached). This is a safety feature. The Kick will tell you this feature is activating when you experience STUTTER VAPE (vapor-no vapor alternating). If you continue to vape beyond this indicator, the Kick will stop functioning until a fresh battery charge is detected.

The Kick is designed to be used only as specified in these instructions. Using the Kick module in any configuration other than as outlined above will VOID THE WARRANTY and will be at your own risk. EVOLV cannot warranty, or be responsible for, any user modifications to the device and/or any application other than as specifically described in these user instructions.

Please follow the link below for the operating instructions and video demonstration: http://www.evolvapor.com/kick/
Package Contents:
  • 1 x The Kick by Evolv

Average Customer Review: 4 of 5 Total Reviews: 17 Write a review

  0 of 0 people found the following review helpful:
one big problem January 8, 2014
Reviewer: anthony from NJ United States  
ok so I got the kick and I was like I cant wait to use it and then I put it in one of my mods and It worked great and then I wanted to put it in a different mod and well the this crappy copper spring snaps right off when I tried to take it out so my 45.00 dollars worked for like 3 hours and then broke I hope that myvaporstore will help me fix this problem so when I here from them I will make anther review

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Kick in the NUTZ! November 3, 2013
Reviewer: David Haenchen from St. Charles , MO United States  
I received my kick and it doesn't seem to work I have tried it on every setting and it seems my mod works better without it. I think it might be defective. Waiting to hear from MVS about exchanging it.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Waste of money for mech mod READ Y October 31, 2013
Reviewer: Jason Wolfe from Studio City, CA United States  
This is a waste of money if u build low ohm coils.If u throw a dual coil or single on a mech mod you get the full power out of the hit. Why would u want to limit yourself with a kick?

Was this review helpful to you?

  0 of 0 people found the following review helpful:
It has it's uses... October 10, 2013
Reviewer: Doug Beatty from Magnolia, DE United States  
Well MyVaporStore did make good on the money I spent for the kick and even sent me a replacement. I sent both of them back for store credit. One stone cold dead and one working intermittently at best.
 This makes sense if you just have to use a factory medium resistance atomizer on a mech mod. For myself? I'll wrap a 1.3 ohm coil and use a protected battery. More wattage than this version of the kick can do and the battery is still protected from short/overcharge/overdrain.
 For those without skillz who must be seen with a manly mech mod in hand, proceed. Good luck on getting one that deosn't fizzle out promptly. :)

Was this review helpful to you?

  0 of 0 people found the following review helpful:
I recommend it. July 5, 2013
Reviewer: Vince Fajardo from Honolulu , HI United States  
Works really good!!

Was this review helpful to you?

View All Customer Reviews